Psion Teklogix PowerScan M8300 Manuel d'utilisateur télécharger pdf (Page 78)

PEN EMULATION

The operating mode parameters are complete commands and do not require reading the

Enter and Exit configuration codes.

PERATING

ODE

 interpret mode

Ì$]8Î

Interprets commands without sending them to the decoder.

transparent mode

Ì$[4Î

Sends commands to the decoder without interpreting them.

1 2 ... 73 74 75 76 77 78 79 80 81 82 83 ... 219 220

Psion Teklogix 1
PowerScan 1
D8330/M8300 1
COMPLIANCE 7
LASER SAFETY COMPLIANCE 9
LED CLASS 10
IC (INDUSTRY CANADA) 10
1999/5/EEC R&TTE 11
CONTENTS 13
GENERAL VIEW 16
Figure C – BC-8000 17
Figure D – C-8000 17
1 INTRODUCTION 18
2 INSTALLATION 19
INSTALLATION 20
CAUTION 20
2.3 RS-232 CONNECTION 22
2.4 USB 22
2.5 IBM USB POS 23
2.6 WEDGE CONNECTION 24
2.8 NETWORK CONNECTIONS 25
2.8.2 Network Cabling 26
2.8.3 Network Termination 27
2.9.2 Replacing PowerScan 28
M8300 Batteries 28
2.9 POWERSCAN 28
M8300 BATTERY MAINTENANCE 28
2.9.1 Battery Charging 28
2.10.1 Desktop Mounting 30
Portable Desktop Use 31
Fixed Desktop Use 31
2.10.2 Wall Mounting 33
Inclined Base Wall-mounting 34
3 POWERSCAN 35
M8300 SYSTEM AND NETWORK 35
LAYOUTS 35
3.1.4 C-BOX Layout 37
3.2.1 Host Master Layout 38
3.2.2 BC-8060 Master Layout 39
/*32: FAIL*/ 40
4 CONFIGURATION 41
4.1.3 Copy Command 42
4.2 SETUP PROCEDURES 42
Ì$+$*oÎ 44
ÌIB'Î 45
ÌRA0RFHÎ 46
Ì$+RN0$-IÎ 46
Ì$+RX0$-qÎ 47
Ì$+RN1$-NÎ 47
4.5.2 PowerScan 48
4.6 POWERSCAN 49
M8300/STAR-SYSTEM™ SETUP 49
Ì$+RF4Î 51
Ì$+RZ2$-ÇÎ 52
Ì$+RZ1$-~Î 52
Ì$+CP0$-$Î 53
Ì$+CM2EC0$->Î 53
Ì$+CM1$-ÈÎ 53
Ì$+CM0$-ÃÎ 53
Ì$+CP6$-BÎ 53
First Start-Up 56
CONFIGURATION 58
RS-232 PARAMETERS 59
ANDSHAKING 61
USB PARAMETERS 64
USB-COM 65
USB-KBD 67
EYBOARD 67
ATIONALITY 67
WEDGE PARAMETERS 70
HARACTER 76
MULATION 76
PEN EMULATION 77
PERATING 78
NETWORK PARAMETERS 82
ERMINATOR 86
DATA FORMAT 87
DJUSTMENT 93
EPLACEMENT 95
POWER SAVE 100
READING PARAMETERS 101
NTENSITY 104
DECODING PARAMETERS 107
CODE SELECTION 110
Ì#+AUTOWÎ 111
ADVANCED FORMATTING 128
ONCATENATION 129
DVANCED 132
ORMATTING 132
RADIO PARAMETERS 147
ONTROL FOR 150
DISPLAY PARAMETERS 153
5 REFERENCES 157
5.1.2 ACK/NACK Protocol 158
5.1.3 FIFO 159
5.1.4 RX Timeout 160
5.2 PEN PARAMETERS 160
5.2.1 Minimum Output Pulse 160
5.2.3 Overflow 161
5.2.5 Inter-Block Delay 162
5.3 NETWORK PARAMETERS 162
5.4 DATA FORMAT 163
POWERSCAN® D8330/M8300 167
(accent) 168
ÌFQ9C2>Î 170
5.4.3 Address Stamping 172
5.4.4 Address Delimiter 172
5.4.5 Time Stamping Format 173
5.5 POWER SAVE 173
5.5.1 Sleep State 173
REFERENCES 174
5.6.5 Safety Time 175
5.7 DECODING PARAMETERS 175
5.7.1 Ink-Spread 175
5.7.2 Overflow Control 175
5.7.3 Interdigit Control 176
5.8 ADVANCED FORMATTING 176
5.8.1 Match Conditions 176
5.9.2 Radio RX Timeout 177
5.9.3 Power-Off Timeout 177
5.9.4 Transmission Mode 178
5.9.6 Single Store 179
5.9.7 Batch Mode 179
5.9.8 Find Me (PowerScan 180
M8300 only) 180
5.10.1 Display Mode 181
Ì$+$0ÂÎ 183
Ì$+$1$Î 183
Ì#+CODEÂÎ 183
Ì$+ZZ0$-*Î 184
Ì$+ZZ2$-4Î 185
Ì$+ZZ3$-9Î 186
Ì$+RN2$-SÎ 188
6 MESSAGE FORMATTING 189
6.1.1 Cursor Control 190
6.1.2 Font Selection 191
6.1.3 Clearing Display 191
6.1.5 Setting RTC 192
7 TECHNICAL FEATURES 194
7.2 POWERSCAN 195
7.3 BC-80X0 / C-8000 196
7.5 STATUS INDICATORS 197
7.6 READING DIAGRAMS 200
POWERSCAN 201
SERIAL CONFIGURATION STRINGS 202
(ms) CK00 - CK99 203
(100 ms) CL00 - CL99 203
(not for USB-KBD-ALT-MODE) 204
(IBM AT compatible only) 204
(100 ms) CK00-CK99 206
(only for D8330 series) 209
B CODE IDENTIFIER TABLE 215
C HEX AND NUMERIC TABLE 218
HEX / NUMERIC TABLE 219

Commentaires sur ces manuels

Pas de commentaire

Psion Teklogix PowerScan M8300 Manuel d'utilisateur Page 78

Commentaires sur ces manuels