Psion Teklogix 7525M Manuel d'utilisateur Page 74
- Page / 206
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 7: 100-Pin Connector
Connector Position And Orientation
64 Psion Teklogix WORKABOUT PRO HDK User Manual
7.1.3 Connector Position And Orientation
Figure 7.2 WORKABOUT PRO Back View Showing The 100-pin Connector
7.2 100-Pin Connector Pinout
Pin names in the following table are those used on the WORKABOUT PRO.
Battery compartment
Standard placement of Pin 1
Placement of Pin 1 on
the WORKABOUT PRO
100-pin connector
Table 7.1 Pinout of the WORKABOUT PRO 100-Pin Connector
Pin Name Function
Signal
Direction
Active
State
During
Reset
State
During
Sleep
Pull-up
value
(ohms)
1 V_IN Power N/A
2 V_IN Power N/A
3 V_IN Power N/A
4 V_IN Power N/A
5SD0 System data
bus
Input/output Hi-Z Low
6SA0 System
address bus
Output Low Low
Abbreviations:
N/A= not applicable;
B = both high and low,
Hi-Z = high impedance.
- Psion Teklogix 1
- WORKABOUT PRO HDK 1
- What is RoHS? 4
- RoHS Logo 4
- TABLE OF CONTENTS 5
- Chapter 7: 100-Pin Connector 7
- Chapter 8: Scanner Connector 7
- Appendices 9
- Contents 10
- INTRODUCTION 1 11
- 1.1 About This Manual 13
- 1.2 Text Conventions 14
- 1.3 Contents Of The HDK 14
- Chapter 1: Introduction 15
- Files In The HDK 15
- 1.4 Obtaining The HDK 16
- 1.6 Discontinued Hardware 17
- HARDWARE 2 19
- 2.1 Overview 21
- 2.3 WORKABOUT PRO C, S, M, ME 21
- 2.3.2 Peripheral Processors 22
- 2.4.1 Main Processor 23
- 2.4.2 Peripheral Processors 23
- GoForce 4000 Media Processor 24
- This provides the following: 24
- • Video controller 24
- 2.5 Identifying Hardware 25
- 2.6 The LED 25
- 2.7 Connectors 25
- 2.8 Power Management 25
- 2.8.1 Batteries 26
- 2.10 Connector Locations 27
- SOFTWARE 3 29
- 3.1 Overview 31
- 3.2 Windows Drivers 31
- 3.4 System Initialization 32
- 3.5 Registry Keys 32
- HardwareFlowBaud (REG_DWORD) 33
- FFUART (REG_DWORD) 33
- PCMCIA (REG_DWORD) 33
- USB (REG_DWORD) 33
- 3.6 COM Port Assignments 34
- 3.7.1 Installing The Software 35
- Chapter 3: Software 36
- Development Platforms 36
- 3.7.8 The USBhub Namespace 37
- 3.7.10 The smBus Namespace 37
- 3.7.11 The PCMCIA Namespace 37
- MECHANICAL CONSIDERATIONS 4 39
- 4.1 Overview 41
- 4.2 HDK Mechanical Files 41
- WORKABOUT PRO 42
- WORKABOUT PRO 2nd. Generation 42
- 4.3 Installation 43
- 4.4 Location And Construction 44
- 4.4.3 Expansion Module 45
- Endcap, Card Stop, And Stylus 46
- Back view with the 46
- 4.4.5 Bottom Footprint 47
- EXTERNAL CONNECTORS 5 49
- • LIF connector 52
- • Tether connector 52
- • Power connector 52
- GND SP+L MIC+ SP+L 58
- 5.6 Docking Stations 59
- 5.7 Vehicle Cradles 62
- 5.8 Port Replicator 64
- Port Replicator 65
- 5.9 Other Cables And Adaptors 66
- INTERNAL CONNECTORS 6 67
- 6.1 Overview 69
- 6.4 100-Pin Connector 70
- 6.5 Scanner Connector 70
- 100-PIN CONNECTOR 7 71
- 7.1 Overview 73
- Hi-Z = high impedance 74
- 7.4 Data And Address Buses 80
- 7.5 Serial 80
- 7.7 General-Purpose I/O 81
- 7.9 PCMCIA 82
- 7.10 Wakeup 83
- 7.11.1 I2C Addresses 84
- Chapter 7: 100-Pin Connector 85
- Example Expansion Modules 86
- Psion Teklogix Serial Endcaps 87
- SCANNER CONNECTOR 8 89
- 8.1 Overview 91
- 8.2 Scanner Kits 92
- 8.4 Scanner Connector Pinout 93
- 8.5 The Scanner Flex 95
- 8.6 Power And Ground 95
- V+5_BAR 5 V 300 mA 96
- V+3.3 3.3 V 1 A 96
- Chapter 8: Scanner Connector 97
- Signals To The Scanner Device 97
- 9.1 Overview 101
- 9.2 Example Scanner Boards 101
- Serial Scanner Board 102
- Scan Engine Connector 104
- Intermec, scan engines 104
- 9.3 Power And Ground 106
- 9.4.2 USB Signals 107
- 9.4.3 Control Signals 107
- 10.1 Overview 111
- 10.2 Installation 111
- 10.3 Dimensions 111
- 10.5 Electrical 112
- The Card Detect Signals 113
- 10.6 EEPROM Data 114
- 11.1 Overview 117
- 11.2 Schematics 118
- 11.3 Connectors 118
- Abbreviations: 119
- N/A= not applicable; 119
- B = both high and low 119
- L= active low 119
- The USB Host 1 Connector (J6) 122
- 11.4 Configuration 123
- 11.4.1 Slot Power Control 124
- 11.4.2 EEPROM Write Control 124
- 11.5 Power And Ground 128
- 11.6 EEPROM Data 129
- 11.7 Installation 129
- Installation 130
- APPENDIX A 131
- A.3 Worldwide Offices 132
- International Subsidiaries 133
- APPENDIX B 135
- APPENDIX C 137
- C.2 Radio Specifications 140
- C.3 Scanner Options 141
- C.4 Battery Specifications 141
- High-Capacity Battery Pack 142
- APPENDIX D 145
- D.2 WORKABOUT PRO C Variant 147
- D.3 WORKABOUT PRO S Variant 148
- D.4 WORKABOUT PRO ME Variant 148
- D.6 Radio Options 151
- D.7 Scanner Options 151
- D.8 Battery Options 151
- APPENDIX E 153
- E.1.1 WORKABOUT PRO C Variant 155
- E.1.2 WORKABOUT PRO S Variant 155
- WORKABOUT PRO All Variants 156
- E.2 Radio Options 160
- E.3 Battery Options 160
- E.4 Scanner Options 160
- Scanner/Imager Model Numbers 161
- APPENDIX F 163
- F.1 Radio Specifications 165
- F.5 Bluetooth Radio 167
- APPENDIX G 169
- G.2 Scanner Specifications 171
- G.2.1.1 SE 1223HP Decode Zone 172
- G.2.1.2 SE 1223LR Decode Zone 172
- G.2.1.4 SE 955HP Decode Zone 173
- G.3 Imager Specifications 174
- HHP5180 Imager Specifications 175
- SX5393 Imager Specifications 176
- *QR code 177
- **Data Matrix 177
- 1D Bar Codes 178
- SX5400 Imager Specifications 179
- APPENDIX H 181
- H.1 Battery Specifications 183
- H.2.2 Standard Discharge 184
- H.2.3 Environmental Test 185
- H.3.2 Standard Discharge 187
- H.3.3 Safety Data 188
- H.3.4 Safety License 188
- H.3.5 Environmental Test 188
- H.4.2 Standard Discharge 190
- H.4.3 Safety Data 191
- H.4.4 Safety License 192
- H.4.5 Environmental Test 192
- APPENDIX I 195
- I.2 GRANT OF LICENSE 197
- LIMITATIONS 197
- I.4 HIGH RISK ACTIVITIES 198
- I.5 DISCLAIMER OF WARRANTY 198
- I.6 LIMITATION OF LIABILITY 198
- I.9 ENDING THIS AGREEMENT 199
- I.10 GENERAL 199
- I.8 CONFIDENTIALITY 199
Produits connexes et manuels pour Stations d'accueil pour appareils mobiles Psion Teklogix 7525M
(24 pages)
(7 pages)© 2020, manymanuals.fr. Tous droits réservés | 4.260 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels