Psion Teklogix 7525M Manuel d'utilisateur Page 58
- Page / 206
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 5: External Connectors
Cables For the Tether Connector
48 Psion Teklogix WORKABOUT PRO HDK User Manual
5.4.2.1 Sensing Device Presence
For device identification, in the connected cable, one of the following pull-down resistors must be
connected between TETHER_DETECT (pin 7) and ground:
The Psion Teklogix Mobile Devices SDK enables a software application to detect and identify the
connected device.
5.4.3 Cables For the Tether Connector
Psion Teklogix provides cables that connect to the tether port of the WORKABOUT PRO. For a
complete list see www.PsionTeklogix.com/Accessories
.
These cables include the following:
• Tether to RS-232-C cable for the WORKABOUT PRO 2nd. Generation.
• Tether to USB-B for the WORKABOUT PRO 2nd. Generation.
• Tether to USB-A for all WORKABOUT PRO variants.
5.5 The WORKABOUT PRO C, S, M, ME Audio Connector
The audio connector is only available on the WORKABOUT PRO C, S, M, and ME. It is not
available on the WORKABOUT PRO 2nd. Generation computers.
The audio connector has the following pinout:
The audio connector accepts a standard 2.5 mm stereo minijack.
Figure 5.5 Audio Plug
Pull-down Resistor Device
200 kΩ USB client.
100 kΩ USB host.
49.9 kΩ USB serial.
Table 5.3 Pinout Of The Audio Connector
Pin Signal Name Description
1 SP+R Right speaker positive.
2 MIC+ Microphone positive.
3 SP+L Left speaker positive.
4 GND Ground.
GND SP+L MIC+ SP+L
- Psion Teklogix 1
- WORKABOUT PRO HDK 1
- What is RoHS? 4
- RoHS Logo 4
- TABLE OF CONTENTS 5
- Chapter 7: 100-Pin Connector 7
- Chapter 8: Scanner Connector 7
- Appendices 9
- Contents 10
- INTRODUCTION 1 11
- 1.1 About This Manual 13
- 1.2 Text Conventions 14
- 1.3 Contents Of The HDK 14
- Chapter 1: Introduction 15
- Files In The HDK 15
- 1.4 Obtaining The HDK 16
- 1.6 Discontinued Hardware 17
- HARDWARE 2 19
- 2.1 Overview 21
- 2.3 WORKABOUT PRO C, S, M, ME 21
- 2.3.2 Peripheral Processors 22
- 2.4.1 Main Processor 23
- 2.4.2 Peripheral Processors 23
- GoForce 4000 Media Processor 24
- This provides the following: 24
- • Video controller 24
- 2.5 Identifying Hardware 25
- 2.6 The LED 25
- 2.7 Connectors 25
- 2.8 Power Management 25
- 2.8.1 Batteries 26
- 2.10 Connector Locations 27
- SOFTWARE 3 29
- 3.1 Overview 31
- 3.2 Windows Drivers 31
- 3.4 System Initialization 32
- 3.5 Registry Keys 32
- HardwareFlowBaud (REG_DWORD) 33
- FFUART (REG_DWORD) 33
- PCMCIA (REG_DWORD) 33
- USB (REG_DWORD) 33
- 3.6 COM Port Assignments 34
- 3.7.1 Installing The Software 35
- Chapter 3: Software 36
- Development Platforms 36
- 3.7.8 The USBhub Namespace 37
- 3.7.10 The smBus Namespace 37
- 3.7.11 The PCMCIA Namespace 37
- MECHANICAL CONSIDERATIONS 4 39
- 4.1 Overview 41
- 4.2 HDK Mechanical Files 41
- WORKABOUT PRO 42
- WORKABOUT PRO 2nd. Generation 42
- 4.3 Installation 43
- 4.4 Location And Construction 44
- 4.4.3 Expansion Module 45
- Endcap, Card Stop, And Stylus 46
- Back view with the 46
- 4.4.5 Bottom Footprint 47
- EXTERNAL CONNECTORS 5 49
- • LIF connector 52
- • Tether connector 52
- • Power connector 52
- GND SP+L MIC+ SP+L 58
- 5.6 Docking Stations 59
- 5.7 Vehicle Cradles 62
- 5.8 Port Replicator 64
- Port Replicator 65
- 5.9 Other Cables And Adaptors 66
- INTERNAL CONNECTORS 6 67
- 6.1 Overview 69
- 6.4 100-Pin Connector 70
- 6.5 Scanner Connector 70
- 100-PIN CONNECTOR 7 71
- 7.1 Overview 73
- Hi-Z = high impedance 74
- 7.4 Data And Address Buses 80
- 7.5 Serial 80
- 7.7 General-Purpose I/O 81
- 7.9 PCMCIA 82
- 7.10 Wakeup 83
- 7.11.1 I2C Addresses 84
- Chapter 7: 100-Pin Connector 85
- Example Expansion Modules 86
- Psion Teklogix Serial Endcaps 87
- SCANNER CONNECTOR 8 89
- 8.1 Overview 91
- 8.2 Scanner Kits 92
- 8.4 Scanner Connector Pinout 93
- 8.5 The Scanner Flex 95
- 8.6 Power And Ground 95
- V+5_BAR 5 V 300 mA 96
- V+3.3 3.3 V 1 A 96
- Chapter 8: Scanner Connector 97
- Signals To The Scanner Device 97
- 9.1 Overview 101
- 9.2 Example Scanner Boards 101
- Serial Scanner Board 102
- Scan Engine Connector 104
- Intermec, scan engines 104
- 9.3 Power And Ground 106
- 9.4.2 USB Signals 107
- 9.4.3 Control Signals 107
- 10.1 Overview 111
- 10.2 Installation 111
- 10.3 Dimensions 111
- 10.5 Electrical 112
- The Card Detect Signals 113
- 10.6 EEPROM Data 114
- 11.1 Overview 117
- 11.2 Schematics 118
- 11.3 Connectors 118
- Abbreviations: 119
- N/A= not applicable; 119
- B = both high and low 119
- L= active low 119
- The USB Host 1 Connector (J6) 122
- 11.4 Configuration 123
- 11.4.1 Slot Power Control 124
- 11.4.2 EEPROM Write Control 124
- 11.5 Power And Ground 128
- 11.6 EEPROM Data 129
- 11.7 Installation 129
- Installation 130
- APPENDIX A 131
- A.3 Worldwide Offices 132
- International Subsidiaries 133
- APPENDIX B 135
- APPENDIX C 137
- C.2 Radio Specifications 140
- C.3 Scanner Options 141
- C.4 Battery Specifications 141
- High-Capacity Battery Pack 142
- APPENDIX D 145
- D.2 WORKABOUT PRO C Variant 147
- D.3 WORKABOUT PRO S Variant 148
- D.4 WORKABOUT PRO ME Variant 148
- D.6 Radio Options 151
- D.7 Scanner Options 151
- D.8 Battery Options 151
- APPENDIX E 153
- E.1.1 WORKABOUT PRO C Variant 155
- E.1.2 WORKABOUT PRO S Variant 155
- WORKABOUT PRO All Variants 156
- E.2 Radio Options 160
- E.3 Battery Options 160
- E.4 Scanner Options 160
- Scanner/Imager Model Numbers 161
- APPENDIX F 163
- F.1 Radio Specifications 165
- F.5 Bluetooth Radio 167
- APPENDIX G 169
- G.2 Scanner Specifications 171
- G.2.1.1 SE 1223HP Decode Zone 172
- G.2.1.2 SE 1223LR Decode Zone 172
- G.2.1.4 SE 955HP Decode Zone 173
- G.3 Imager Specifications 174
- HHP5180 Imager Specifications 175
- SX5393 Imager Specifications 176
- *QR code 177
- **Data Matrix 177
- 1D Bar Codes 178
- SX5400 Imager Specifications 179
- APPENDIX H 181
- H.1 Battery Specifications 183
- H.2.2 Standard Discharge 184
- H.2.3 Environmental Test 185
- H.3.2 Standard Discharge 187
- H.3.3 Safety Data 188
- H.3.4 Safety License 188
- H.3.5 Environmental Test 188
- H.4.2 Standard Discharge 190
- H.4.3 Safety Data 191
- H.4.4 Safety License 192
- H.4.5 Environmental Test 192
- APPENDIX I 195
- I.2 GRANT OF LICENSE 197
- LIMITATIONS 197
- I.4 HIGH RISK ACTIVITIES 198
- I.5 DISCLAIMER OF WARRANTY 198
- I.6 LIMITATION OF LIABILITY 198
- I.9 ENDING THIS AGREEMENT 199
- I.10 GENERAL 199
- I.8 CONFIDENTIALITY 199
Produits connexes et manuels pour Stations d'accueil pour appareils mobiles Psion Teklogix 7525M
(24 pages)
(7 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.851 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels